28
Sep
The seller is oboverstockparts and is located in Saint Petersburg Florida. Point 90 fitting toward pulse hose.
1 - Cut and plug the oil line at the engine so that the oil side of the.
Vro pump conversion to straight fuel pump. Just a quick video to go over my 130hp Evinrudes VRO to fuel pump conversion. 438559Order of hoses from back of pump to front. VRO Pump Conversion To Straight Fuel Pump J.
Reeves You can convert the VRO pump into a straight fuel pump eliminating the oil tank and VRO pump warning system but retain the overheat warning setup and fuel restriction warning if so equipped by doing the following. VRO PRE-MIX REPLACEMENT PUMPS IF YOUR VRO PUMP IS DAMAGED OR YOU JUST PREFER TO PRE-MIX JUST REPLACE IT WITH A NON-OILING PUMP FROM MASTERTECH. All Pumps On This Page Require Pre-mixing 501 fueloil in fuel tank.
24 rows Easy to follow instructions fuel hose and additional zip ties are included with each pump. Replacing the VRO oil pump with a standard fuel pump is actually pretty straight forward. Replacing the VRO Oil Pump.
Get the Right Parts to replace the oil pump. First get a replacement fuel pump. You can buy these on ebay There is also a good website that can help you select the correct fuel pump for your engine.
MasterTech Marine can guide you in selecting the right fuel pump for you outboard. You can convert the VRO pump into a straight fuel pump eliminating the oil tank and VRO pump warning system but retain the overheat warning setup by doing the following. 1 - Cut and plug the oil line at the engine so that the oil side of the VRO pump will not draw air into its system.
Trace the wires from the back of the VRO to its rubber plug electrical plug and disconnect it. Johnson VRO Conversion Good choice going to the right pump. I just disconnected my vro so I have one piece of advice make sure you disconnect the wiring harness to the vacuum valve.
If you dont it will give you an out of oil alarm. Trace the wiring from the vro pump to the valve. You will find a harness with three wires about halfway in between.
You can convert the VRO pump into a straight fuel pump eliminating the oil tank and VRO pump warning system but retain the overheat warning setup by doing the following. 1 - Cut and plug the oil line at the engine so that the oil side of the VRO pump will not draw air into its system. VRO Replacement Fuel Pump Kit - Johnson Evinrude 25-140hp 90-degree.
Inline Fuel Filter 516 - Universal. Fuel Filter - Universal Evinrude Etec 40-200hp. Gasket Carburetor to Airbox - Johnson Evinrude 3cyl.
Converting to a conventional fuel pump will probably cost you around 15000 - 20000 in parts but you will be saving at least that much in labor. Another benefit of the conventional fuel pump if it ever goes out you can rebuild it. There will be a bolt with 38 head and a screw driver slot in head of bolt on port side of block a little behind the VRO pump and a bolt hole on each side of bolt That bolts blocks off the pulse hole remove bolt to operate diaphragm style fuel pump.
You would need to order mounting screws and gasket to use this style fuel pump. Check to see if the pulse fitting in the old pump is a straight or a 90 fitting. Place thin O-ring 10 in pulse fitting hole first then insert pulse fitting 11 or 12 in pump.
Point 90 fitting toward pulse hose. 7 Secure with a smaller retainer 13 and screws 14. It was than that I said to myself OK Im going to remove the fuel oil pump and do away with the VRO and just mix my own oil and install a new fuel pump.
In case your interested a fuel oil VRO pump is 400 and a straight fuel pump is 35 so I removed the big unit and installed a straight fuel pump. This replacement fuel pump kit fits V6 60 Looper models. It replaces the VRO pump mounted to the vapor tankbracket system mounting directly to the tankbracket in place of the VRO pump using our custom-made bracket and custom aluminum hose fitting.
Our custom fitting will not crack or deteriorate as plastic fittings might and is held securely. Pump the bulb and engine runs well for 20 seconds at WOT or maybe 2 minutes at low idle. Id like to replace the original fuel pump and oil mixing pump VRO.
In an archived post someone mentioned. In case your interested a VRO pump is 400 and a straight fuel pump is 35 so I removed the big unit and installed a straight fuel pump. VRO Pump Conversion To Straight Fuel Pump J.
Reeves You can convert the VRO pump into a straight fuel pump eliminating the oil tank and VRO pump warning system but retain the overheat warning setup and fuel restriction warning if so equipped by doing the following. 1 - Cut and plug the oil line at the engine so that the oil side of the. 175109 436203 438094 435560 438400 435953 435556 435558 435784 0175109 5004558.
4-Wire replacement fuel pump kit. Used on all motors except 2 cylinder 40-50 HP. 3This kit services a VRO2 pump that has the 4-wire warning system or services a VRO style fuel only pump.
I believe it may be the VRO pump. I am looking to replace the VRO pump part number 5007420. The cheapest new OEM one is about 460.
I would leave the oil side disconnected as it now. However during my research it also appears there is a VRO to premix conversion pump that may work 5007422. I believe it will use existing mounting brackets.
This VRO system conversion non-oiling fuel pump for 90hp-250hp Johnson Evinrude Outboard motorsfits V6 Crossflow and Looper engines but DOES NOT fit 60 degrees applications. Top equipment quality ensure our fuel pump have most reliable performance and long life timeWe specialize in each partalways provide you genuine products. Johnson VRO to fuel only change pump Previous owner removed the oil tank unpluged the electrical for the oiler and has been premixing the fuel.
Ive just rebuilt both carbs and was still having trouble with the motor under the cups. It was acting like it had too much air mixing with the fuel so I was going back over the hose fitings. The item FuelVRO Oil Injection Conversion Fuel Pump Kit for Johnson Evinrude 5007422 is in sale since Wednesday January 11 2017.
This item is in the category eBay MotorsParts AccessoriesBoat PartsOutboard Engines ComponentsOther. The seller is oboverstockparts and is located in Saint Petersburg Florida. This replacement fuel pump kit fits V4 90 120 130 140 HP models and 90 V6 Looper and Crossflow motors.
It replaces the VRO pump mounted to the external bracket on the block. Detailed mounting instructions are here. Most 200 - 275 HP and some 175 HP motors have a different bracket than the smaller V6 models.
Instructions for those are here. Also included are 2 extra pieces of hose if needed. Optional conversion replacement for Johnson Evinrude VRO Fuel Oil Pumps for engines 3 CYLINDER AND LARGER ONLY.
Replaces the following previous kit part number 0438402. Wiring is not required for pump 5007422. The wiring is for low oil alarm which will not be required with this conversion.
This kit services a VRO pump that has a 4 wire warning system or services a VRO style Fuel Only pump.