Replacing steering cable on boat

However many folks opt to do it themselves as the boat steering cable replacement job. Attach the new cable to the helm and insert the cotter pin to secure the connection.

Note that my steering system is a rack pinion system.

Replacing steering cable on boat. Steering Cable Replacement. Make Your Boat Drive Like New - YouTube. Make Your Boat Drive Like New.

Replacing a boat steering cable can be challenging but its a repair that is totally doable for the mechanically-inclined boat owner. Inspecting Replacing Your Boat Steering Cable - Marine Parts Source. Always replace your boat steering cable with the same type that had been originally installed.

Rack with rack hydraulic with hydraulic and rotary with rotary. This way your craft will continue to handle as well as it did the first time you took her out on the water. Look at the casting numbers and letters on the cable jacket and on the helm.

Those markings will determine what type of cable you will. I have replace steering cables on IO before but never on an inboard. I have an 85 mastercraft and the steering is tight.

I do not see the part number on it but have been told it is a 14ft cable. Does anyone know what the correct lenght is before I order. What are the basic steps to changing the cable.

I had to cut the cable 2x to get it out of the steering tube. It is not a straight shot from the tube to the access hole. What i did was modified the access port so that the cable can be changed without loosening removing the motor i just love cutting holes in my boatThe more i look at my boat the more i question some of the design the engineers put into it.

The Basics On How To Lube Steering Cable On Boat. When lubricating the steering cable on your boat you will need to have a few things on hand. These include the following.

Stainless steel steering tilt tube. Nut with zerk fitting. At some point in every boats life if it has mechanical steering youre going to have to replace the steering cable.

In the case of this particular cable that I have in front of me its from a rotary helm and once you take the cable off the boat if you look at the engine end of. Disconnect the old steering cables from aft end of boat. Note that my steering system is a rack pinion system.

That means that each cable has a permanently attached push rod on one end and a permanently attached rack on the other end ie. The end that is. Attach the new cable to the helm and insert the cotter pin to secure the connection.

Run the new steering cable along the same path that the old cable followed to the tilt tube. Liberally apply marine grease to the end of the new cable and push it through the tilt tube. Thread the 916-inch nut back into place and tighten with an adjustable wrench.

9 If replacing an old cable with a threaded end at the helm you will need to thread on a quick-connect adapter onto the helm the new cable will snap into the new adapter. 10 Thread the new cable into the helm by turning the steering wheel until the cable clicks into its locked position. The best way to remove the cable is to remove the pin out of the clevis at the end of the cable where it attaches to the rudder arm then remove the clamp block that holds the steering tube.

Pull the whole assy out Then you can get at the 1 18 nut that holds the cable in the tube. For outboard boats under 25 feet you can expect a replacement steering cable to cost under 130. Teleflex systems are particularly effective where the installation requires long cable runs andor multiple bends between the helm and the engine.

Ive heard this could cause stiffness in steering as well. With our maintenance background it shouldnt be a difficult task at all. However a problem I run into is that theres no room to pullinsert the cable inout of the pivot tube.

Im probably going to have to remove the motor to change the cable. Steering is okfor now. I have a 1989 Stratos 201 PRO boat with a 200 HP Evinrude V6 Motor.

My steering is very difficult. I guess my cables are bad. It has rack pinion steering.

GlenI fought this problem a few years ago except my problem was the steering rod end being siezed in the engine mount tilt-tube. Teleflex cable is not designed to be de-sleeved and R. Its a unit replace item.

If you are willing to do that itll cost you probably 120 or so USD for a new cable assembly assuming its about 14 length. Boat Steering Cable Replacement Cost Estimate. Boat steering cable replacement cost at a dealership will run you anywhere from 300-650 depending on the make and model of your boat.

However many folks opt to do it themselves as the boat steering cable replacement job. Grease around the end of the cable housing then replace the rubber seal. Re-install the locknut cable end then attach it to the jet nozzle.

I used Mobil 1 because its a low viscosity oil and will protect well. Any light oil will work. Id recommend doing this every year for a boat thats used in salt water every other year for fresh water boats.

Replacing old school steering cable. N good job on finishing that up and staying with the cable and sheave arrangement. Many large comml boats use these and they work fine.

People just dont want to have to messs with the details on those as. You can now pull the steering cable out. If you run into tight quarters turn the steering wheel or pull the cable end at the wheel since you have the cable disconnected there.

When you reassemble use a good grade of waterproof grease on the output end and a little on the threads of the cable nut. The cable nut must be secure. -unbolt steering cable box from steering wheel gear 4 bolts -pull cable from helm towards rear of boat sometimes you may also need to push the trailing part cable towards the front of the boat.

-once i got the bitter end of the cut cable into the ski locker i connected a wire to make sure i could pull the new one back through if needed.