Mounting depth finder transducer inside hull

They want you to use something that will set up without bubbles or voids and that has no. Greg thats essentially how my transducer Airmar P79 mounts.

Even though there is some loss of signal in shooting through the hull your LCR will perform well with this type of installation.

Mounting depth finder transducer inside hull. Mounting Depth Finder Transducers Inside the Hull. Manufacturers frequently recommend using epoxy or similar substance if you decide to bond a transducer to the inside of the hull. They want you to use something that will set up without bubbles or voids and that has no.

To determine the best place to mount the depth transducer you can do a simple test with the help of a plastic bag filled with water. Connect the depth transducer to the instrument as described in the manual. Place the transducer inside the bag with water and hold the transducer against the hull to see if you.

Place the transducer inside a thin plastic bag partially filled with water and cinched tightly with a cable tie. Wet the mounting surface and press the active face of the transducer against the hull. Compare the bottom return to the baseline and if the reading is similar the mounting location is good.

You could also mount the transducer inside the boat provided the boat has a solid fiberglass not-cored hull. This has the added benefit of avoiding drilling a hole in the boats bottom. To check use a plastic baggie filled with water and try the transducer in various spots on the hull.

The transducer is mounted inside of the hull usually in a bilge sump or keel permanently adhered to the hull with an epoxy or may be contained in a liquid reservoir. The sonar ping emitted from the transducer must penetrate a solid unblemished hull material to effectively record a sounding. If its ON the KO icon will be illuminated on the depth finder display.

You will need to set the keel offset to zero. Now hold the transducer over the side of the vessel so that it is the same distance below the water surface as it would be at the in-hull mounting location. Note the depth that is being displayed on the Depth Sounder.

Mounting fish finder transducer inside hull of aluminum boat On an Aluminum boat I would use a 38 to 12 half aluminum block instead of wood or starboard. Also I used plain Silcone seal on my Aluminum boat back in 1981. I might use 4200 but.

Here are some common inside-the-hull transducer models for deepwater applications from Airmar Technology and used by many fish finder brands. P79 Plastic hull-mount kit 600 watt single or dual frequency 50200 kHz which can be adjusted from 2 to 20 degrees to accommodate for the hulls. A good way to find a good place to build a box to mount a transducer in your hull is to fill a ziplock bag with water make sure there is no air in it.

Then you can wet the inside of the hull where you think you might like to mount the transducer lay the bag of water in that spot then place the transducer ontop the bag. Take the boat for a spin and see what its like. You can find the perfect spot without.

Im replacing my old BG depth sounder which has a through-hull transponder with a new Furuno model having an in-hull transponder. The new transponder is fitted into an Airmar P79 base attached to the inside of the hull and is set down into a fluid bath contained in the base. Install Fish Finder Transducer in Hull - YouTube.

This Video Short from the makers of HawkEye fish finders and depth sounders explains how to glue a depth sounder or fish finder transducer inside a boat hull. A trailing transducer when it plows through the water parting it is certain to generate one of a multitude of problems when the transducer is installed inside of the suggested 15. Potentially this can create burned areas on a prop blade 2 Ventilation.

A transducer dragging or plowing anywhere below the running surface of a boat will part the water just as a plowed furrow a farmer makes in a. Any depth finder you have or buy you can mount its transducer in the same location as the factory one would. Personally I would NEVER pay that outrageous price for the factory depth gauge when for 200 you can have SO much more information at your fingertips.

Greg thats essentially how my transducer Airmar P79 mounts. It comes with a plastic cylinder base which is cut at an angle and flanged on one end. This end is placed on the hull rotated until the top end is perfectly level and siliconed down.

After curing it gets filled with propylene glycol and the ducer gets sealed inside. See how to install the Garmin Striker 4 fish finder transducer inside the hull of your kayak using duct seal. See how to mount your transducer on your kayak.

After marking the location of the transducer remove the water from inside the hull. Thoroughly dry the mounting surface. Mix an ample quantity of two-part slow-cure epoxy.

Coat the face of the transducer and the inside of the hull. See the illustrations Transducers with Directional Bias and Transducers without Directional Bias. Identify your transducer shape to determine how it needs to be oriented inside the hull.

In-Hull Transducer In-Hull Transducer. In-hull or shoot-thru transducers are stuck to the inside of fibreglass hulls they will not work with aluminum wood or steel hulls or with hulls that have foam padded pockets. Any wood metal or foam layers on top of the fibreglass hull will need to be removed in order for the in-hull transducer to work.

For displacement hull powerboats locate the transducer 13 of the way along the LWL and 6 to 12 off the centerline. For planing hull powerboats mount it well aft near the centerline and well inboard of the first set of lifting strakes to ensure that it is in contact with the water at high speeds. Repeat this process until a good location for the transducer is found.

Dry out the bilge completely and clean the hull surface where the transducer will be mounted. The transducer will be attached to the hull with a two-part epoxy glue and water or dirt will degrade the inherent sound transmission characteristics of the glue. Scott F I think he got a 2d unit for depth OP a skimmer transducer for 2d shouldnt lose depth if mounted correctly.

Also I have a HB SI transducer mounted to a spring bracket from TSS. I dont lose depth until above 30mph. You can epoxy a transducr to the inside of the hull.

Macgregor 22 Olympia. I just purchased a Lowrance Elite 5 depth finder w GPS. To avoid drilling holes in the hull I opted for a shoot through the hull transducer.

The instructions for placement are a tad vague but what is very clear is that once the unit is placed using the marine epoxy it cant be moved. Inside Hull Mount- The high speed transducer can be mounted inside the hull without pivot assembly using the proper two-part epoxy such as Humminbirds epoxy kit. Even though there is some loss of signal in shooting through the hull your LCR will perform well with this type of installation.

Ad Great Prices On Transducer Depth. Find It On eBay. Everything You Love On eBay.

Check Out Great Products On eBay.