07
Jun
Removes the transducer from the trolling motor to prevent transducer wire from winding on the motor and removes potential for interference from the motor electronics. One side can hold a livewell pump and the transducer mounts on the other side.
However if mounting on the starboard side is not possible it is ok to mount it on the port side keep in mind that readings may not be stable all the time because the upstroke of the propeller on the port side causes pulses to be.
Mounting a transducer on a pontoon boat. Stainless steel screws bolts etc. Are a necessity when mounting your transducer. This material is more resilient against forming rust and it should keep your transducer in place as long as you want it hooked to your pontoon boat.
Double-check all hardware as non-rust resistant materials can appear the same as stainless steel at a glance. Transducer Placement on a Pontoon Boat Lets make sure we are talking about the proper location. The bracket is not on the top or bottom of the pontoon log.
Its at the back of the pontoon log close to the bottom. Think of the back as a dinner plate. Weld a U shaped aluminim bracket so it does not extend below the pontoon.
Originally when we purchased the boat the transducer was mounted to the back of a pontoon tube. Unfortunately the mount was one that did not have the flip-up feature found in the newer fishfinder models. Basically it did not flip up when bumped from the front or when cruising at high speeds as the newer models do.
Eventually after a couple of beachings the transducer. One side can hold a livewell pump and the transducer mounts on the other side. On an electric drive you will not likely be traveling at any great speed so the water passing between the tubes will not be overly disturbed so I would think mounting it on the transom would work ok.
We cant see you pontoon but if the transducer is in the water it should be fine. DIY Transducer Mount for Inflatable Pontoon Boat. If playback doesnt begin shortly try.
Anyway Im going to mount it on our pontoon. In the past on other boats I mounted the transducer inside the hull using epoxy these were all fiberglass boats. My pontoon has the usual mounting bracket on the end of the toonTo keep the transducer from being torn off I was hoping to mount it inside the bracket using epoxy Has anyone tried this and will the transducer.
Procedure Of Installing A Depth Finder On A Pontoon Boat Step 1. Find The Best Depth Finder For Pontoon Boat. Find The Right Location For Transducer.
Correct Placement Of Monitor. Buy Extra Stuff Needed For Installation. Settle The Wires.
Outrigger style transducer mount for fiberglass and aluminum boats. Allows the user to place the transducer at the front of the boat to see what is directly below. Removes the transducer from the trolling motor to prevent transducer wire from winding on the motor and removes potential for interference from the motor electronics.
Dragging a trailing transducer mounted closely to the transom and below the hull in the trough of a boat forces a powerful flow of already disturbed water into around and over the transducer creating all sorts of sounding chaos. We have accepted this as customary for transom-mounted transducers simply because this is what weve been instructed to doand do our best to deal. I just bought a 220 24 foot tritoon.
The tubes have the lifting strakes mounted on them. I have mounted a depth finder transducer on the mounting bracket but am unable to get the depth finder to work properly. Id mount a transducer plate near the bottom of my pontoon then attatch the transducer to the plate.
Secure the plate tot he pontoon. Be sure and mount the bracket as close to bottom as possible. Toons make lots of bubbles and disturbed water and transducer needs clean water to work right.
Dont tighten so much it wont kick up when it hits something. If your pontoon boat does not have a mounting bracket for the transducer use an aftermarket transducer bracket. Writer Bio This article was written by a professional writer copy edited and fact checked through a multi-point auditing system in efforts to ensure our readers only receive the best information.
The easiest way to install a transducer on a boat or kayak. Dont drill holes or use glues when installing your transducer. Rather use our magnetic transducer mounts.
Works on all materials. Also get the best transducer mounting solutions for your inflatable boat or kayaks here. We are making transducer mounting easy.
How to install a lowrance transducer on a pontoon boat A pontoon is a boat that has a flat bottom and which is placed on floats. It can be simply built by closed cylinders such as pipes or barrels and can be used to support a simple platform creating a raft. Locate a place on the dashboard for a suitable mounting position.
Use the special. When transom mounting a transducer on a pontoon boat try to mount the transducer on the starboard side pontoon. However if mounting on the starboard side is not possible it is ok to mount it on the port side keep in mind that readings may not be stable all the time because the upstroke of the propeller on the port side causes pulses to be.
Mounting a transducer on the bow of a boat separately from a trolling motor is a solution to issues we fishermen have with the questionable joining of a trolling motor and a high resolution transducer. The Bow-Ducer Outrigger mount our new product name is a solution to all transducer and trolling motor issues. The Bow-Ducer Outrigger mounts to the opposite side of.
Fixing a transducer is a very easy step ie. Drill double holes at a 14 portion at below of the fish finder mounting brackets of your pontoon boat. You must verify that the tube is not punctured.
After putting it connect the transducer fixing with nut washer and with bolts. Installing the Stern Saver on a boat NO DRILL transducer mount - YouTube.