How to tell if your pontoon has water in it

Flashback is on the right track. The purpose of a pontoon boat lift is to make boating easier by enabling you to launch your vessel from dock to water and then elevate it safely to the upright position when you return to your dock.

If you notice your boat sitting lower in the water or one pontoon sitting significantly lower than the other there is a good chance that there is water in one or more pontoon.

How to tell if your pontoon has water in it. To check if your pontoon boat has water in it do the following. Listen for sloshing water inside the boat. Check for leaks dents or corrosion where water could have leaked in.

Be aware of how long the boat has sat outside of water. It could be condensation. Water in Pontoons Linda.

Flashback is on the right track. You need to locate the hole or holes first. I had two previous pontoon boats that developed leaks in the logs.

These were aluminum hollow logs welded together in sections. Each section had a ½ inch nipple welded on top with a plug screwed in to make them water tight. Response from Matt in Godfrey Pontoons Customer Support.

The tubes are chambered. Each vent plug is for each chamber in the tube. Over time it is not uncommon for water to get into the tube from condensation.

If there is a LOT of water in the tubes then they will need to be inspected for leaks. Typically this should be done by a Godfrey dealer. Hearing water in tube.

So the boat shop says there is a crack where the front deck mount is mounted to the toon and small crack in the nose of the cone. Also he said that there was a hole drilled in the bottom of the nose cone with a machine screw in it. By HandymanHerb Thu Sep 04 2014 830 pm.

A lot have hole on the bottom in the baffles you can get water in all sections but it air locks like when you put an empty glass in water upside down and keeps the water from filling the toon and are easy to drain if you do get water in them. How to drain water out of a pontoon - YouTube. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features.

If you are riding lower and lower you are getting water in the pontoons. Your pontoons have several chambers in them and each one has to be checked for water. If you go to the back of each pontoon and look towards the front you will see several posts sticking out of the top.

Each one of those is a separate chamber that can get water in it. Keep an eye on it and empty out any water that accumulates in the bottom. Besides your engine not running or running poorly a periodic visual check of the fuel water separator on you engine is the best way to see if water is beginning to accumulate in your fuel system.

You will also want to make sure that your pontoon logs are positioned straightly. If you are sailing in salt water you will need to make sure you keep track of your pontoon tubes and whether or not the metals are being destroyed and corroded by the saltwater. You really need to take the time to find that tiny leak.

You can use a hair dryer or weak air source to barely pressure the toon and then go over all seams and welds with soapy water. Chances you will find some bubbles. Handling a pontoon boat on and off the water will also be a deciding factor especially if its only for individual use while small pontoon boats may be perfectly manageable fully laden larger vessels may be dangerous to crew single handed especially if you are inexperienced or new to the water.

A pontoon boat is considered a flat-bottomed boat because its hull has a relatively shallow draft which generally. A basic design starts with two plain round tubes that come to a point at the front of the boat. They are typically made of marine-grade aluminum that has been welded.

Within the tubes you will find the fuel tanks as well as a place to store your belongings. On top of the tubes manufacturers weld support channels for the deck using cross beams. If the contents of the jar appear to have a clear bubble at the bottom gas floats on water remember there is some water contamination.

Siphon the water from the bottom of the tank. If phase separation from ethanol and water mixing this bubble will be a gelatinous white as shown in the photo you likely need to call an environmental services company to safely dispose of this bad fuel. To know if your pontoon boat has pressurized pontoon tubes simply visit the manufacturers website or call a local authorized dealer.

They will likely tell you that it doesnt matter if they are pressurized or not. It doesnt really matter unless of course they have a leak. Rinse your pontoon boat with distilled water and you are done.

All the corrosion and streaks are gone and your pontoon boat has a silver appearance. You can get professional results with a bit of practice. You can also used the drain plug to fill the pontoons with a water hose to see where exactly the leak is.

If not you can also use an air compressor to fill the pontoons with pressure to listen for a hissing sound indicating where it leaks. Now that you have followed safety measures it is time to start your pontoon boat. Turn the ignition or motor to the on position and wait about 1-5 minutes for the engine to warm up.

Once you are ready to take off trim the pontoon motor so that the boat is sitting in the water at a shallow level. And if water has gotten inside there must be a hole somewhere that needs to be repaired and the pontoon re-pressurized. Is this something a marina normally handles or a boat repair shop.

Its listing a little bit in the waterbut not to bad. Dont know much about pontoons but I have seen containers that had a lot of water in them because water could build up around inspection plates and such in a puddle and then leaked in around a bad seal due to the heating and cooling of the tanks. Oil drums had this happen often when they had been opened and the bung not screwed back in all the way.

Avoid using a pontoon boat in water bodies where there is the chance of high waves or stormy conditions. Always check the weather forecasts before setting off. If you see a storm approaching take the boat back to shore.

Keep the weight on the pontoon. The beauty of tell tales is the simple fact most people are totally aware of that continuous stream of water exiting the side of their Out Board motor. When the tell tale stops They stop and start checking for possible causes.

So if your tell tale stops while your out on the water Dont give up all hope hollowing out for a tow. The purpose of a pontoon boat lift is to make boating easier by enabling you to launch your vessel from dock to water and then elevate it safely to the upright position when you return to your dock. Without a boat lift you would need to either leave your boat in the water or.

If you notice your boat sitting lower in the water or one pontoon sitting significantly lower than the other there is a good chance that there is water in one or more pontoon. Please note that you may notice one pontoon sitting slightly lower than the other when your gas tank is filled.