31
May
Clean the interior of your boat and make sure there is no excessive moisture. Cut a slit at the lowest point of the shrink wrap.
Use the rub rail as a starting point measure the distance to the highest point of the boat.
How to shrink wrap a boat. In this video were taking a look at the tools and supplies needed to shrink wrap a boat. Materials mentionedShrinkfast 998 Heat Gun. For boats that are wider than 16m the stand will be placed at the side of the boat and the shrink wrap pulled over the boat from side to side in strips number of strips depending on the length of the boat.
Place the film on the stand so that as you unroll it the folds of the film are facing upwards. This quick how-to video shows you how to shrink wrap your boat for storage. Supplies premium 100 virgin resin shrink wrap in widths of 12.
You need to build a ridge in the center of the boat with two-by-four lumber and it should be supported with the same cord thats used to secure the bottom edge of the wrap around the boatexactly the way Atlantic Shrink Wrap does it in the video. Cut a slit at the lowest point of the shrink wrap. Knot an additional band on the perimeter band.
Run the additional band under the belly of the boat to the other side. Repeat the process placing belly bands every 3 to 5 feet along the length of your boat. Seal all of the pleats in.
Use the rub rail as a starting point measure the distance to the highest point of the boat. Likewise measure from the rub rail down to the water line. This is essentially the area that the wrap will cover.
Winterizing your boat and preparing it for shrink wrapping are the best ways to keep it protected while in storage. Most shrink wrap installations cover the entire boat wrapping the stanchions under the cover and overlapping the top of the hull. Many canvas covers leave holes for stanchions or stop at the cap rails all of which allows more moisture.
A short how-to video showing boat owners the easiest way to remove shrink wrap from a boat for recycling and the necessary steps boat owners need to take to. Place your shrink wrap material over the boat. Run it over the perimeter band and then tuck the excess material behind the perimeter band.
You may need to trim excess shrink wrap near the bow and stern of the boat. In these sections the shrink wrap will be folded into pleats. Use a Heat Gun to Shrink Wrap the Boat.
Begin to shrink wrap your boat. How to Shrink Wrap a Pontoon Boat Dr. You might need a ladder for this one.
Find the sheets midline and drape it over the center of your pontoon boat lengthwise. Then unfurl the edges of the shrink wrap so that it drapes over the sides of the boat. Straighten it out to make sure that the boat is covered evenly across all planes.
Clear the most popular among sales allows customers to view the boat while still wrapped. During the shrink wrapping process the boat frame will be prepared the gas vents will be taped the belly band will be installed and the boat will be wrapped. After the boat has been wrapped the exterior will be cleaned and inspected.
Use tape to create zippered doors for easy access and ventilation when you shrink wrap your boat. When you are ready to shrink wrap your boat for the off season look no further than Pro-Tect Plastics for all of your shrink wrap needs. There are plenty of companies and marinas that will winterize your boat for you using shrink wrap.
Winterizing boat costs depend on the size of your craft and where your boat is. For those of you who want to shrink wrap a boat that is sitting in the water - although that is entirely possible it might cost you approximately between 100 and 150 dollars more. Trailers This will only apply to the smaller boats but it is well worth the mention - if your boat will not sit in one place during the offseason and you plan to move it around on a trailer go for what is referred to as a bullet wrap.
Learn how to shrink wrap a pontoon boat in the following steps. Prepare Your Pontoon for Storage Step 2. Come Up With the Support Structure Step 3.
Install the Shrink Wrap Step 4. Add Vents to the Shrink. The stages of shrink-wrapping a sailboat.
1 Prepare the interior and exterior of the sailboat. If your boat is currently in the water it must be put in dry dock. Clean the interior of your boat and make sure there is no excessive moisture.
Open the hatches and drain plug so that any water still in the boat. SHRINK WRAPPING A PONTOON BOAT. Instead of tucking the shrink wrap film under the perimeter band the shrink wrap needs to be put on the boat before the strapping.
The perimeter band is then installed over the shrink wrap just below the decking. How much does it cost to have a boat shrink wrapped. A shrink wrap can cost between 500-5000.
The installation fee varies depending on how big your boat is. You can expect to spend around 12-25 per square foot. So if you have a big boat expect to pay more.
But you also have the option to shrink wrap your boat by yourself. Shrink-Wrapping your boat is easy. Do-It-Yourself and save.
Protects against weather damage. Its waterproof it can fully encapsulate just about anything. Cover entire flatbed loads and boats 60 with one piece.
See below for videos and for step by step shrink wrapping. Boat Shrink Wrap Alternatives. Marinas boat storage facilities and boat owners can reduce the plastic waste in the world by eliminating or recycling boat shrink wrap.
Boats need protection in the winter season or when being stored so there needs to be a solution. But one-time shrink wrapping can be very harmful to the environment.