How to install a transducer on a aluminum boat

Using a 4 mm 532 inch drill on marked locations. Using a 4 mm 532 inch drill on marked locations.

Get you a transom mounting plate that way you only have drill 2 holes to install it and you can move or add a different transducer down the road without having to drill more holes in your boat.

How to install a transducer on a aluminum boat. If mounting a transducer on an aluminum boat we must place a self-adhesive tape above the drill hole location to reduce cracks in the gel coat layer. Using a 4 mm 532 inch drill on marked locations. Attach the sealant to the supplied 20 mm bolts and attach a transducer assembly to the stern mirror.

Position Your Mounting Plate then Make Drill Marks. To me the best position is at least half an inch from the bottom of the boat. Hold the plate in that position with one hand.

Then using a cordless drill and bit make drill marks on your boats transom with the plates mounting holes as. Skimmer Transducer Install and Lowrance LSS2 - Aluminum Boat Project 9 - YouTube. This is how to properly install a Lowrance HSTWSBL or HSTWSU transducer along with a StrusctureScan HS LSS2.

Mounting SonarPhone Transducer in Aluminium Boats - YouTube. If playback doesnt begin shortly try restarting your device. Find a piece of aluminum or grp tube large enough to hold the transducer and bond it to the bottom with epoxy.

Mount the through hull transducer in a plastic cap and place it on the tube after youve poured enough oil or brake fluid in the tube so the transducer will be submerged completely. Keep the lid in place with some silicone or tape. You might want to consider installing a starboard plate use bolts not screws generous with sealant at holes the back of starboard and then seal around the edges.

Once this is installed you can screw your transducer to the board. This will allow you to move or change transducers down the road without having to put new holes in your hull. How to install a transducer on a aluminum boat manual Files for free and learn more about how to install a transducer on a aluminum boat manualThese Files contain exercises and tutorials to improve your practical skills at all levels.

If you mount it on the transomstarboard to make up the ledge difference. Just screw right into the transom. Mark the board drill your holes on the back of the board put a think ring of Life Seal around the screw holes then just attach your transducer to the starboard.

Use the Life Seal on that too. How to Install a Boat Transducer Mounting Plate Easy DIY - YouTube. Place the transducer inside a thin plastic bag partially filled with water and cinched tightly with a cable tie.

Wet the mounting surface and press the active face of the transducer against the hull. Compare the bottom return to the baseline and if the reading is similar the mounting location is good. Whats going on everybody Rob here with a little video and installing the Stern saver transducer mount for your boat.

We just purchased a brand-new fiberglas. Find a scrap of treated lumber rip yourself a piece about 1 X 15. Mount your transducer to it use a C-clamp to hold it on the transom once youre in the water.

Use a thin scrap of wood under the clamp inside the boat to protect that surface if needed. When mounting the transducer make sure it does not interfere with the carrying of the boat. Do not over-tighten the transducer mount fixing nut.

The transducer can not start if an object is hit in the water which could damage the transducer. Be careful when installing the. Mounting transducer on aluminum jon boat Mount it inside close to the transom on a surface that will allow the cone to cover the area you want covered.

Flat bottom john no problem. SemiV may have to move it away from the centerline to get a flatter surface. Use a 2 part epoxy rough up the boat and the bottom of the puk and glue her down.

New boat and I need to install a transducer on aluminum hull I was told about 5200 and then read it was for fiberglass and wood hulls. Any one with insight that can help would be. How to mount install a transducer on a john boatMounting a lowrance hook2 triple shot transducer to a john boat.

In this video I take you through step by ste. Babooze has it right. Use some Starboard or UHMW through bolted and sealed with 5200 and then mount your transducers to it.

That way WHEN you replace the transducer you dont have to worry about putting yet more holes in the transom. Make the plate large enough 6 wide at the minimum IMHO for expansionadjustments later on while you are at it. Get you a transom mounting plate that way you only have drill 2 holes to install it and you can move or add a different transducer down the road without having to drill more holes in your boat.

I just drill holes and caulk with 100 silicone lifetime caulking and works for me. The biggest reason you cant install a transducer in an aluminum boat like you did the fiberglass boat is that the aluminum is blocking the signal. Sonar signals can read through fiberglass quite fine as long as there are no air bubbles in the epoxy that secures the transducer to the hull.

It doesnt work like that with aluminum and standard.