11
Dec
Can I wax my RV decals. Then feel the gelcoat that you just wiped and you will notice it is much softer and can be marked with your finger nail.
Razor blades no matter how careful you are will dig into the gel coat leaving gouge.
How do you remove decals from gelcoat. Easy way to remove stripes stickers and decals from the your boats Gelcoat. No solvents or chemicals. I removed my stickers this past spring.
I used a new small putty knife and a heat gun hair dryer. Heat the surface with the gun and the sticker will easily remove without damage to gel coat. I then used acetone to remove any glue left behind.
I then had them stencil new numbersthey look great. Go ahead put some acetone on a rag and wipe your gelcoat down if it is dark colored gel you will be surprised the color transferred to the rag. Then feel the gelcoat that you just wiped and you will notice it is much softer and can be marked with your finger nail.
RV decal removal part 3. Darren explains the nature of gel coat and removing RV decals - YouTube. RV decal removal part 3.
Darren explains the nature of gel coat and removing RV decals. This product will restore weather-exposed surfaces eliminating ghost sign images from vehicle surfaces covered by graphics. Just spray Ghost Off onto the oxidized surface wait about a minute and agitate the area with a soft brush.
Rinse from top to bottom and watch the the oxidation flow away. I replaced a side decal on my 88 Centurion and it took me a couple of hours to get the surface clean. Then I used oxidation remover on the side to help blend the gel coat color that was under the decal.
Then re-waxed the area before the new decal was placed. Enitre project took about 3 hours from peel off to new decal. When you place a decal over a fiberglass surface you notice the quick adhesion that is difficult to reverse.
Scraping away the decal in an attempt to remove it can leave residue behind. By using the proper cleaning ingredients to remove the decals from the start you will get rid of both the decal and any adhesive without damaging the fiberglass. Remove Gel Coat Oxidation From Your RV by Hand Buffing.
In this video Wade Weiss from Wade Maid demonstrates how to rejuvenate your dull and oxidized gel coat by hand. In the video Wade uses a simple fiberglass restorer to improve the finish of the model RVs fiberglass. As Wade demonstrates restoring fiberglass gel coat by hand.
Since that was shading and protecting the gelcoat beneath it theres usually a brighter shadow left behind and theres no simple way to remove that although careful compounding and polishing of the hull may blend it in. Do not use this method on colored gel coats or painted hulls such as Hatteras which has an Imron surface. The next step is to polish to a high gloss.
A third method for removing an old boat name from gel coat and in some cases a linear polyurethane surface is. Theres really not much to it. Run the wheel along the vinyl gauging the pressure you need to use by what youve just removed and you should have no trouble.
The eraser wheel will not remove the adhesive though. Thats where lacquer thinner comes in. Soak a rag with lacquer thinner and rub the adhesive until it starts to dissolve.
If you havent bought that Goo gone yet. Ordinary mineral spirits on a rag and some elbow grease is all you ever need to remove sticker or tape residue off of gelcoat. And post 6 is right on the money with his pencil and repeated careful water sanding using the finer grit papers.
If such is your case you may have to remove the decal. Start by heating the design. Peel off the decal from the surface and apply an adhesive remover on a piece of microfiber cloth.
Leon is right. Isopon do do a stripper for GRP. Funnily enuff its called glass stripper.
Bit misleading really as its strips paint and not the glass. Ive used it on grp car bodies. The active ingreadients are different from nitromorse and the like.
The smell is pretty pungent. Works well and if you go to the car factors its not that costly. Removing RV Oxidation with Hand Buffing Work the polish into the surface by hand and polish until you dont feel any more resistance.
Allow the polish to dry and haze over. Finally wipe off the haze with a clean dry cloth to reveal the shiny surface underneath. Top it off with a quality marine or RV grade wax.
Can I wax my RV decals. After removing the decal youll be left with tacky vinyl adhesive like sticker residue on the window. Remove the residue from the window.
If you have a spray residue remover spray it directly onto the sticky residue. Use your plastic razor blade or razor scraper to work the residue loose from the window glass. Soak paper towel with adhesive remover.
Wet a large area of adhesive maybe a foot square Take edge of card and gently scrape off the old adhesive. Once adhesive and decal residue is completely gone follow up with a glass cleaner to prepare surface for the new decal or just leave it bare. As boats get older the decals and striping tape start to peel and crack.
Over the years Ive seen boat owners attempt to remove damaged stripes with razor blades. This is the wrong way. Razor blades no matter how careful you are will dig into the gel coat leaving gouge.