25
Aug
The standard pontoon wall thickness is 081 090 and 125There are solid welded chambers every 5 and each pontoon has a full length under keel and side keel for added protection. One of the major advantages of a pontoon boat is that they are spacious and.
How to Fix Aluminum Boat Leaks with JB Weld Marine Weld - YouTube.
Fixing leaks in aluminum pontoons. For leaking rivets and seams a coat or two or three of our aluminum filled moisture cured urethane – ALUTHANE – will often do the trick. This is a very thin coating with seeps into tiny leaks. It also provides a fresh aluminum paint surface that makes old boats or repaired boats look like new.
Clean the area around the source of the leak with a rag. Sand the area using a coarse-grit sandpaper. This will flatten any surface inconsistencies and help the adhesive bond to the aluminum.
The pontoon boat hits a rock or a wave that opens a leak. The trip is over before you planned. But if you had HTS-735-11 in your tool kit you can make a permanent repair quickly and save the trip.
HTS-735-11 will give you the ability to make repairs on the spot. All you need is a torch a wire brush and HTS-735-11 Fluxless Aluminum Brazing Rod. Repairing Aluminum Pontoons TY Jergeo and Vice Admiral.
My professional maintenance shop has tested each section of the pontoons with air pressure and soapy water. Only one small leak was found. It will be welded.
The seal on the rear starboard pontoon section was broken and exposed as small 14 in hole on top on the pontoon. I think the easiest thing to do to find the leak would be to first put about 3-4 pounds of air pressure in the pontoon. If you cant hear a leak right off use a solution of dishwashing soap and water and apply to the pontoon with a brush.
The leak will cause bubbles to form and its not hard to see the problem. Pontoon tube leak - YouTube. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features.
Fill small punctures with putty according to its directions. Allow the putty to cure then sand it to smooth. For areas with pinholes mix putty with prepared epoxy sealer to a rollable consistency and then roll andor brush it to cover the area.
Wait for the putty and epoxy to dry. How to Fix Aluminum Boat Leaks with JB Weld Marine Weld - YouTube. If playback doesnt begin shortly try restarting your device.
Videos you watch may be added to the TVs watch history and. Keep your boat level and hooked up to your tow vehicle for this step. With a garden hose fill the boat with an inch or two of water paying careful attention to the aluminum underside for any drips or leaks.
Once found use a waterproof marker to highlight areas that need attention. If none noticed continue with the filling process. Ok guys Ive been welding and fabricating for about 12 years now and my boss wants me to fix some leaks in his pontoon.
Welding aluminum is no problem for me but Ive never welded on a pontoon and when I googled it it came back with a guy blowing up. This boat doesnt have an internal gas tank and the tanks it does have are off. I just had one of my logs leak on a brand new Benni.
It turned out to be an easy fix. A couple of hours and 200 later life was good again. To get a new pontoon and replace it would be costly and time consuming.
Plus theres no guarantees that the new one wont leak. Just get it fixed by reputable welder and itll probably be better than new. Jun 28 2012.
So to make a long story short had some welding done to the pontoon and now have quite a few pinhole leaks. Looks like a coat of epoxy is in order. The toons were pretty beat up anyways and have always wanted to have them coated.
It can also be cheaper to fix a pontoon boats issues and pontoons are easier to clean than traditional v-hull boats. Pontoon boats can also be very safe and sturdy due to their multi-hull type design. This allows them to be flatter and more stable in the water.
One of the major advantages of a pontoon boat is that they are spacious and. How do you fix a leaking pontoon boat. Inspect the pontoon for damage.
Move the pontoon to a dry location. Clean the area around the source of the leak with a rag. Obtain aluminum putty from your local marina or hardware store.
Sand the repaired surface with a fine-grit sandpaper once the putty has dried. Our aluminum pontoons are made with type 5052 H32 an aluminum magnesium alloy most resistant to corrosion in fresh and sea water. The standard pontoon wall thickness is 081 090 and 125There are solid welded chambers every 5 and each pontoon has a full length under keel and side keel for added protection.
I really do not want to trailer the boat 14 miles to an aluminum welder if I can avoid it. Noticed the small hole when boat was pulled for the winter. Not alot of water drained from the toon and it was not apparent when sitting in the water.
2000 Tracker Fishin Barge21. Cruzin Lakes Bay NJ Atlantic City NJ Life is a trip without a road map. There are two main ways of fixing a leak in a pontoon boat.
The first is welding the damaged area to cover it up and reseal it. The second is using a steel or aluminum compound putty to repair the area. Welding is generally considered to be better but much harder for the average person to do themselves.
Prepare the pontoon for release of the foam into the cavity by cleaning the area around the leak with an alcohol solution. Alcohol will evaporate and leave the area around the leak dry. Rub the area with a cloth and find the hole in the exterior of the pontoon.
Aluminum Trailers At Magic Tilt we make the most complete line of Aluminum Trailers in the industry. It will be welded. Our indoor showroom area spans over 100000 square feet.
Almost all pontoon boats made for recreational use in the US are made out of 6061T-6 Aluminum in 063 approximately 15 gauge. Full service marine mechanic on staff. Bought a roll of 12 x 10 Aluminum Flashing - cost 2397 Pop-Rivet Gun - 2298 Since pontoons are baffle chambered and not sealed chambered I filled pontoons with compressed air and used soapy water to find all leaks.