Best place to mount transducer

Transducer Location Nearly every boat sold today has a transducer installed by either the factory or a dealer. Do not mount the transducer behind strakes struts fittings water intake or discharge ports or anything that creates air bubbles or causes the water to become turbulent.

Apply a water based lubricant to the transducer face and press.

Best place to mount transducer. Transducer Distance between keel or chine - Your high speed transducer when using the SternMate system is best located with exceptions from the keel to no greater than 70 outboard either port or starboard of the keel. While making a steep bank generally will. I just bought a Lowrance Elite 9 Ti2 with active imaging 3-in-1 and am looking for recommendations best place to mount the transducer on my Nitro 901CDX.

From my research I am looking at placing behind my 10 Bobs Machine Shop hydraulic jack plate as there is lots of room for it and I have a nice flat spot on the hull. Transom mount transducers are obviously mounted directly on the boats transom at the stern of the boat. The transducer needs to be located in the water and usually just below the level of the hull.

Transom mount transducers are usually plastic are the most common type used and are the cheapest of the transducer types available. Should be in the aft of the boat. Do not mount the transducer behind strakes struts fittings water intake or discharge ports or anything that creates air bubbles or causes the water to become turbulent.

The vessels hull that is directly underneath the transducer must be in constant contact with the water. Also the manual states The transducer should be mounted in a location that is high enough on the transom so it is out of the jet stream when the boat is on plane Later on it then says it could be mounted on the step. I was wondering if anyone that has a mega imaging transducer can tell me the best place to mount it.

To determine the best place to mount the depth transducer you can do a simple test with the help of a plastic bag filled with water. Connect the depth transducer to the instrument as described in the manual. Place the transducer inside the bag with water and hold the transducer against the hull to see if you.

It it recommended that you consider installing the transducer on the lower inboard side of the starboard hull. Mounting the transducer too high on the hull may expose it. It should be as close to the centerline as possible but at least 3 inches outside the swing radius of the prop blades.

For twin drives mount the transducer between the drives. Avoid areas abaft through-hull fittings or pickups that create turbulence. DETERMINE THE TRANSDUCER MOUNTING ANGLE.

The general rule of thumb is to mount the transducer to the starboard side which is the down stroke of most single outboard boat propellers right hand lower unit. This side produces the least amount of turbulence and is most efficient in delivering the best performance. The transducer is mounted in a liquid-filled tank inside your vessel bonded to the inner surface of the hull and transmits sonar signals through the hull without direct exposure to the water.

Great for trailer boats theres no external hardware to be damaged during trailering launch and retrieval. Transducer Location Nearly every boat sold today has a transducer installed by either the factory or a dealer. Many have more than one mounted in their hulls.

The majority of these boats have no factory provisions for mounting locations leaving it up to the installer to determine a location that will not negatively affect boat performance. Choose a thru-hull or in-hull transducer and mount it just forward of the leading step. The steps on the underside of the hull create a lot of aeration.

For a transducer to work it must be mounted just in front of the first step before the source of aeration. A transom mount transducer should never be installed on a stepped hull. Mount the transducer as close to the center of the boat as possible.

Do not mount the transducer behind strakes struts fittings water intake or discharge ports or anything that creates air bubbles or causes the water to become turbulent. Where is the best place to mount a transducer I have a 6 meter walk around bayliner and a lowrance finder. Sometimes things that you think will be really complicated end up being easy to fix.

The Marine Electronics Specialist Im going to. Before installing the transducer tank perform one of the 3 methods below in as deep of water as possible. Connect the transducer cable to the fishfinder to verify strong bottom readings.

Flood the area with bilge water. Place the transducer in a garbage bag and fill with water C. Apply a water based lubricant to the transducer face and press.

Usually an optimal place is about 20-40 cm from the keel and mostly to the right it does not always have to be. When determining the right spot it can get a clear reflection and the first great speed of the ship. Recommendations for the best position of installing a transducer Mount.

Ranger says to mount the structure scan transducer on the transom. Good to know they work well even installing that close together. Yes they will FYI the LSS 2 is longer that is why I am going to mount mine now like in the video.

More protection that way. You can install your transducer under the pontoon in a location thats close to your console. On the back of pontoon tubes are brackets that are an excellent location for transducers to stay near the monitor.

Youll be able to drill holes into the bracket and use those to connect the washer nut and bolt that will hold your transducer in place. There are three mounting options for the side imaging transducer. Transom-mount this transducer comes standard with all Side Imaging units.

Trolling motor mount adapters to allow the transom mount transducer to be mounted to the trolling motor are sold separately. Plastic thru-hull transducer offered as an optional accessory. Get a transducer mounting board.

It gives you some wiggle room and no extra holes in the boat. I just put one on and it is really nice for fine tuning the transducer. Yes you can mount the transducer to the jackplate.

In researching new SI units Iv seen a lot of guys using their jackplate as a mounting location.